Garage Door Openers and Parts

Remotes, Keyless Entry and Repair Parts

1st Garage Door Openers, Inc.
 BBB Business Review

For Sales Call 1-480-247-2094

Home
Contact Us
Remotes
Receivers
Keyless Entry and Wall Controls
Repair Parts
Universal
Tec Key Remotes
Wayne Dalton Remotes & Keypads
Lubricant
Multi-Code  300 MHZ and International Freq. 40.685 MHz Frequency

Driveway Alert

Garage Accessories
Shipping/Returns
Warranty Information
Cancellation Policy
About Us
Customer Assistance
Coding Instr.
Fax or check Order form
Site Index
5012 Digi-Code Garage Door Opener Remote Control Transmitter
Remotes
DC5202 Stanley Garage Door Opener Compatible Wireless Keyless Entry
Keyless Entry
Stanley Garage Door Opener Infrared Safety System
Repair Parts

All orders are shipped same or next day!!!

VISA, Mastercard, American Express and Discover

Digi Code Garage Door Opener and Gate Operator Wireless Keypad DC5202 Programming Instructions

Digi-code Wireless Keypad DC5202

INSTALLATION AND PROGRAMMING INSTRUCTIONS

Features

The Mounted Exterior Keypad is a battery-operated device that will operate a Digi-Code receiver or a Stanley garage door opener using a four-digit PIN (Personal Identification Number). Pressing four preprogrammed numbers on the keypad sends a radio signal to the receiver or door opener that controls the garage door or gate operator.

Pressing any key will light the keypad.

The keypad works with both Digi-Code Receivers (DC-5200 & DC5202) and Stanley Digital type door openers. (DC5202 ONLY)

The keypad will store the last PIN entered in its memory, even if the battery is removed.

Pressing any key within 30 seconds after the door have been activate will activate the door again.

**************WARNING***************

·          Mount the Keypad OUT OF THE REACH OF CHILDREN at least five feet above the ground.

·          NEVER allow children to operate the keypad.

·          Disconnect power from the door opener before installation.

·          Wear safety glasses to protector your eyes during installation.

*******************************************

Section 1:  General Installation of Your Exterior Keypad

Tools Required:

- Drill with 1/8” bit

- Flathead screwdriver

- Pencil

- Measuring tape

1.       Choose a location that will not interfere with the normal operation of the door or gate.

2.       Hold the keypad at the selected location. Using your pencil, mark the wall at the center on the top of the unit.

3.       Drill a 1/8” hole 3/4” directly below this mark.

4.       Tighten a screw in the hole until the head is sticking out about 1/16.

5.       Hang the unit on the screw. Adjust screw as required for a snug fit.

6.       Remove the battery cover to expose the second screw hole.

7.       Mark the position of the second screw with the pencil through the screw hole.

8.       Drill another 1/8” hole for the second screw.

9.       Tighten the second screw in the hole.

10.   Install the battery and replace the battery cover.

Section 2:  Identifying Your Type of Stanley Door Opener (Model DC-5202 ONLY)

- Digital openers have toggle switches, jumper wires or rocker switches.

After identifying your opener type, find the section that will help you program your Exterior Keypad:

- Section 3: Programming a Digi-Code Receiver or Stanley Digital Garage Door Opener.

- Section 4: Programming A New Personal Identification Number (PIN)

- Section 5: Clear All Memory – Return to Factory Default Setting

Section 3:  Programming to a Digi-Code Receiver (Models DC-5200 & DC-5202) or a Stanley Digital type Garage Door Opener (Model DC-5202 ONLY).

1.       Refer to the DIP switch settings in your receiver or the back of your opener and take notes of which switches are in the “On” or “Closed” positions. You must have at least 1 of the 10 switches closed.

2.       Press the Radio Learn button twice. The light by the Digi-Code label will come on and stay on.

3.       Press the numbers that represent the closed switches on the receiver or the garage door opener (i.e. if switches 2,4, and 6 are closed, enter 246. For switch position 10, use the 0 key).

4.       Press the Radio Learn button once.

5.       To test if you have properly programmed in the radio code, enter the factory set PIN (1-2-3-4). The receiver or opener should operate.

Section 4:  Programming a new Personal Identification Number (PIN).

1.       Press the Access Learn button twice. After doing this, the light by the Digi-Code label will come on and stay on.

2.       Enter 1-2-3-4 (Factory Default), then your new 4-digit PIN or if you have already programmed your PIN – enter this number and then the new PIN you wish to change it to.

3.       Press the Access Learn button once. The light by the Digi-Code label will turn off. The new PIN number has been accepted.

Section 5:  Clear All Memory – Return to Factory Default Settings.

1.       Press and hold both the Radio Learn and Access Learn buttons for approximately 10 seconds until the lights on the keypad go off. The unit now has a factory default PIN of 1234 and ALL radio codes have been erased.

Normal Operation

When the keypad is programmed properly, the garage door or gate should operate by pressing the four digits of your PIN. The door or gate will activate pressing the fourth number and the indicator light will stay on for one second to show that the signal is being sent to the receiver. The keypad will blink on and off.

After each keystroke, the indicator will light.

After pressing any key, all the keys will light up.

Troubleshooting

The correct PIN must be entered within 20 keystrokes; otherwise the keypad will stop operation for 5 minutes. The user has 25 seconds between keystrokes to enter the correct code.

If you forget your PIN, you will have to reprogram your keypad again. (Refer to Section 3 for Digi-Code receivers or Stanley Digital openers.)

If the keypad lights go off after the first keystroke, the battery needs replacing.

Battery Replacement

The keypad uses a 9-volt battery.

garageopenerparts - Owned by 1st Garage Door Openers, Inc., an independent family owned and operated business serving the Garage Door and Garage Door Opener Industry since 1981.  Providing excellent customer service and assistance for over 25 years. We are a discount reseller of  garage door opener remotes, repair parts, keyless entry and gate operator controls for your home, business, or gated community.   We carry parts for the following garage door openers Lift-Master, Chamberlain, Sears Craftsman, Access Master, Sears Best Craftsman, Sears Automatic Door Opener, Master Mechanic, Security +, Formula 1, Garage Master, Billion Code, LiftMaster Professional, Estate Series, Premium Series, Contractor Series, Power Driver, Whisper Drive, Genie, Alliance, Norelco, Blue-Max, Lift-A-Door, Pro Max, Hercules, Stealth, Excelerator, Intellicode, Genie Pro, OverDrive, Python 2, Signature, Phantom, Legacy, Medallion, CodeDodger, Overhead Door, Genie Shop Vac, Stanley, Vemco, Quiet Glide, SecureCode, Lightmaker, Innovative Products, Whistler, U-Install, Popular Mechanics, Allister, Allstar, Pulsar, MVP, Challenger, GTO, All-O-Matic, Electrolift, Westinghouse, AM/11, Linear, Access Pro, Moore-O-Matic, MegaCode, Delta 3, MultiCode, Heddolf, ESP Micom, Intercontinental Dynamics, Crusader, Wayne Dalton, iDrive, Door Master, Quantum, Classic Drive, Tec Key, Martec, Monarch, Telectron and other garage door openers, and gate operators. Brand names of Garage Door openers are registered trade names of the respective entities and are only used for reference.

Home | RemotesKeyless | Receivers | Repair Parts | Compatibility Chart | Lubricants | Multi-Code 300 MHZ Frequency | Coding Instructions | "Bridged Wire" Instructions | About Us Customer Assistance |  Contact Us | Fax or check | Shipping / Return Policy, Warranty / Cancellation Policy | Tec Key |
1st Garage Door Openers Inc.

Mesa. AZ 85203

1-480-247-2094
1-480-247-3498  Fax
Technical Support  Contact Us

 


Copyright © 2017  garageopenerparts.com.  No part of this site can be reproduced in any form or by any means, photocopying, electronic, mechanical, or otherwise, without the prior written permission of 1st Garage Door Openers Inc.